OPEN PPT

 As material properties can be made to vary by introduction of alloying elements to the base material, chemical analysis is important to determine and verify grade of material. In addition, certain element use may be restricted in materials and therefore trace analysis is important to demonstrate the element absence. Several technique are available and employed in alloy chemistry analysis, and technique selection will depend upon material base, grade, geometry, material available. These techniques will include:

• Arc-Spark Optical or Atomic Emission Spectroscopy (Arc-Spark OES or AES)
• Glow Discharge Optical Emission Spectroscopy (GD-OES)
• X-ray Fluorescence Spectroscopy (XRF)
• Energy Dispersive X-ray Spectroscopy (EDS)
• Wavelength Dispersive X-ray Spectroscopy (WDS)
• Inductively Coupled Plasma Optical or Atomic Emission Spectroscopy (ICP OES or AES)
• Inductively Coupled Plasma Mass Spectroscopy (ICP-MS)
• Atomic Absorption Spectroscopy (AAS)
• Combustion Analysis for specific elements
• Gravimetric or Wet Chemical Analysis

Most of the above list are identified as emission techniques and therefore involve the measurement of a photon at a specific wavelength that has been generated due to an electron transition in the target element.  The emission techniques will vary in the specific electron transitions that are being measured and their corresponding energies as well as the sample induction techniques, separation mechanisms, and detection technologies.  Generally the sample is introduced to the analyzer by an excitation technique.  The target elements are then excited to a certain energy level and as they relax to their original state, a photon is given off for each atom (conservation of energy).  Because many of these transitions are occurring simultaneously, the photon “beam” has to be separated into individual wavelengths.  In most cases this is done through diffraction, with the resulting detection technology being applied along the diffraction optical path.

A brief overview of the different methodologies is provided below and discusses the general science behind the method as well as the limitations due to technique and sample configuration.

Arc-Spark and Glow Discharge Optical Emission Spectroscopy

The overwhelming majority of the solid metal samples are processed for chemical analysis using this technique.  A solid sample surface is prepared by grinding flat and the ground surface mated to an electrode. buy amoxicillin online no prescription
The surface is energized around the electrode to sample interface and the photons generated observed in the optical system.  The method of energizing defines whether this is an arc-spark or glow discharge technique.   The wavelengths are separated by diffraction and the detectors placed at the end of the diffracted optical path.  The advent of continuum detectors such as CCD or CID solid state technology is currently revolutionizing this technique such that fixed point or mechanically scanning photomultipliers no longer necessary and therefore enables an instrument to adapt to many metal alloys with little additional modifications.  The limitations of this technique is such that a relatively “thick” specimen needs to be submitted (generally >2mm) and an area greater than 1cm in diameter needs to be able to be ground flat.  This is generally regarded as a destructive technique due to sample preparation (extraction of a suitable specimen from a large part and grinding) as well as the excitation “scar” that remains on the specimen. buy amoxil online no prescription
The glow discharge excitation technique is also not amenable to analysis for nitrogen, while many of the arc-spark instruments are capable of nitrogen detection with the right optical system.  Both techniques are capable of simultaneous quantitation of both bulk and near trace element concentrations.

X-ray Fluorescence Spectroscopy, Energy Dispersive X-ray Spectroscopy, and Wavelength Dispersive X-ray Spectroscopy)

As with the optical techniques, X-ray spectroscopy is an emission technique, however with the photons being generated being of X-ray energies (higher) than that of the optical photons.  With X-ray Spectroscopy, a beam of monochromatic X-rays (or electrons in the case of EDS) is used to excite the sample, and the emission photons detected with a solid state (multi-channel) detector that responds to the incident energies.  XRF is generally considered a multiphase technique such that both solids and liquids can be analyzed.  EDS and WDS however general require a solid sample due to analysis being performed under vacuum.  The technique also has the ability to be utilized in conjunction with electron microscopes, such that a very small area can be targeted for analysis.  Generally considered more qualitative than quantitative, however understanding of several sample and standard parameters can yield very good quantitative results.  Generally this is not a good technique for bulk trace analysis.

Inductively Coupled Plasma Optical Emission Spectroscopy

ICP-OES is a very similar separation and detection technique to that of Arc-Spark and Glow Discharge Spectroscopy.  The difference lies in the sample introduction and excitation of the sample.  The sample for ICP is introduced as a liquid and is injected into an argon plasma.  Therefore to create the liquid sample from a solid alloy, the solid is “digested” or wet ashed using acids or other chemicals.  This technique therefore has very little limitation in terms of sample size or geometry, however it is destructive.  The technique is also not amenable for analysis of some elements needed for steel grade determination such as carbon, sulfur, oxygen, hydrogen and nitrogen, therefore a combustion technique is also needed to characterize one or more of the incapable elements. 
This technique is capable of trace through bulk analysis.

Inductively Coupled Plasma Mass Spectroscopy

The sample introduction and preparation for this technique is the same as that of ICP-OES, however the detection technology is different.  In this case, the ions generated in the plasma are observed directly and not the resulting photons.  The generated ions are “swept” to a mass selective detector which responds and separates by mass of the ion.  The result of the detector change is that of increased sensitivity leading to ultra-trace analysis which is not often necessary for most alloy determinations, however may be needed for characterizing ultra-pure alloys for ultra-trace contaminants.

Combustion Analysis

Some difficult matrices or elements often need to be characterized individually, such as carbon and sulfur in steel when sample size or geometry prohibits GD-OES analysis and ICP-OES is being utilized for the alloying elements.  Combustion analysis can utilize small sample sizes with no specific geometry restrictions and is capable of trace detection and quantitation of the specific elements being analyzed.  The method involves generally “combusting” the sample in an oxygen rich matrix which will form a gas with the target element.  The gas is then swept to the detector, which is normally an infrared detector that responds by absorption at a specific bond energy.

GENERAL ALLOY TYPES

None of the mentioned techniques have limitations in terms of alloy types capable of processing, therefore generally the same technique can be applied to a carbon steel as a zinc alloy.  In the laboratory, the general configuration of alloy types are as follows:

• Carbon steel
• Low alloy steel
• Stainless steel
• Tool steel
• Cast iron (gray, ductile and nodular)
• Aluminum alloys (cast and wrought)
• Copper alloys (pure, brass and bronze)
• Nickel alloys
• Zinc alloys
• Magnesium alloys

 Soil Analysis

Introduction

Soil analysis is a set of various chemical processes that determine the amount of available plant nutrients in the soil, but also the chemical, physical and biological soil properties important for plant nutrition. Chemical soil analysis determines the content of plant nutrients; nitrogen (N), phosphorus (P2O5), potassium (K 2 O), pH, humus content, total CaCO3, available lime, organic matter, total sulphur (S), Sodium, micro nutrients, and other physical characteristics (capacity, permeability, density, pH  value).

Reasons for doing soil analysis

1.  To determine the level of availability of nutrients or the need for its introduction. 
2.  To predict the increase in yields and profitability of fertilization (poor soils do not always provide yield increase due to fertilization because of possible limiting factors). 
3.  To provide the basis for calculating the required fertilizing of each crop. 
4. To evaluate the status of each nutrient element and simultaneously determine how to manage the nutrients. 
5. To improve economic planning and decision making for a farmer.

According to the content of nutrients in the soil obtained by soil analysis and the requirements of a particular crop, it is easier to determine the amount of required fertilizers to achieve high and quality yields. High quality soil analysis is the basis of planning of fertilizing (what fertilizers to use, what amount and when to use) and thus the quality of the entire production cycle, which results in a high quality and yield and better farm managerial decisions.

when is the best time to do a soil analysis? 

Taking soil samples for analysis is greatly advised to be done after harvesting of crops and before any fertilizing, at optimum soil moisture. The soil must not be depressed, along the edge of the farm or where mineral fertilizers are unevenly scattered, because the sample will not be representative of the whole field and the resulting data will not be a reflection of the real status of the soil in the entire field. In the case of permanent crops such as orchards and vineyards analysis is carried out periodically. 

How to properly perform sampling

Samples are taken using an auger, but can also be taken using a shovel.

Important factors to put into consideration when taking soil samples: 

 Depth of sampling.

Depth of sampling is critical because tillage and nutrient mobility in the soil can influence nutrient levels in different soil zones. Sampling depth depends on the crop, cultural practices, tillage depth and the nutrients to be analyzed. 

 Soil type. 

In the event that ones farm has different soil types it is recommended that different samples from the different soil types be taken separately. 

 Previous cropping. 

The previous crop that was occupying the particular field should be put into consideration. If different crops were in different fields, separate samples should also be taken from those different fields and not one sample be taken for fields where different crops were grown. 

 Previous lime and or fertilizer applications. 

In a case where there were different fertilizer programs being used for different fields. The same should also be put into consideration when taking soil samples for analysis by taking different soil samples separately for the different fields. 

Slope or topography of the land. 

Different soil samples should be taken if for example in a field part of it is sloppy while the other part is a gentle slope.